Mitsubishi Electric P2 Error, Indoor Pipe Sensor Fault

Your indoor unit keeps a close eye on the refrigerant entering and leaving its coil.

One of its most important helpers is a sensor clipped to the liquid pipe. The Mitsubishi Electric P2 error tells you that sensor, or its connection, has stopped reporting sensible numbers. Here is what that means for your system.

What does P2 mean on a Mitsubishi Electric air conditioner?

On many Mitsubishi Electric indoor units, a thermistor sits on the liquid side of the indoor pipework, close to where the thin copper line enters the coil. Service documents often call it the indoor liquid pipe thermistor. It tells the indoor board the temperature of refrigerant at that point.

When the board sees a value that cannot be real, such as zero resistance or an open circuit, it records P2 and stops. In other words, the board has lost one of the measurements it uses to manage refrigerant flow and protect the coil.

What the pipe reading is used for

The liquid pipe temperature is part of a bigger picture. Combined with other readings, it helps the system judge how much refrigerant the coil is receiving and whether the coil is close to freezing. On many models, it also feeds into how the outdoor unit adjusts its expansion valve and compressor speed. Lose that reading, and the system loses part of its fine control. It cannot be sure whether the coil is starving, flooding or about to freeze, so stopping is the responsible choice until someone repairs the sensor.

What do you see when P2 appears?

The code itself is often the first sign, yet a few other clues can appear.

  • The unit stops shortly after starting, and a lamp blinks.
  • A wired controller shows P2.
  • Cooling or heating felt unusual in the days before the fault.
  • Ice formed on the indoor coil now and then.
  • The fault clears with a restart, only to return later.

What usually causes P2?

Because the sensor sits right on the cold pipe, its environment is wet and chilly much of the time.

Moisture getting into the sensor

Condensation forms on the liquid pipe during cooling. Over the years, moisture can creep past the sensor coating or into its lead. Once water reaches the element, readings go haywire.

A sensor that has slipped

A clip holds the sensor against the pipe. If the clip loosens, the sensor may slide away and measure air instead of copper. That alone may not trigger P2, but it exposes the lead to damage and confuses the board.

A damaged lead

The lead runs through the unit to the indoor board. Sharp metal edges, vibration and careless handling during a coil clean can nick it. A broken core reads as an open circuit and triggers P2 quickly. A partly broken core is worse in a way, because it may connect one moment and drop out the next, which leads to the frustrating on and off pattern many owners describe.

Corrosion at the plug

The board plug can corrode in damp conditions, especially if the drain has ever overflowed. Intermittent contact leads to faults that come and go.

Board input failure

Occasionally, the circuit on the indoor board that reads the pipe sensor fails after a surge or with age. In that case, the board needs repair or replacement, and a new sensor alone will not clear the code.

What can you do before calling?

Your options are limited because the sensor sits behind panels, yet a couple of steps are worthwhile.

  1. Turn the unit off with the remote or controller.
  2. Switch off the circuit breaker for a few minutes, then switch it back on.
  3. Try the system once more and note whether P2 returns.
  4. Look for water stains under the indoor unit, which can hint at moisture problems.
  5. Think about any recent coil clean, repair or relocation.

For safe restart steps, see how to reset a Mitsubishi Electric air conditioner.

Stay outside the casing

The pipe sensor connects to the indoor board, which carries mains voltage. Please leave panels and plugs to a licensed technician.

How does a technician deal with P2?

The process is methodical and, in most homes, fairly quick from start to finish.

Gaining access

The technician isolates the power and removes the panels needed to reach the liquid pipe and the board.

Testing the thermistor

They unplug the sensor and measure its resistance, then compare it with the expected value at the pipe temperature. A reading far from the chart confirms a failed sensor.

Following the lead

They trace the lead from the pipe to the board, looking for cuts, crushed sections or corrosion.

Refitting securely

When they fit a new sensor, they clip it firmly to the correct pipe, add any insulation the design calls for and route the lead away from sharp edges and moving parts.

Running a check

They then run the system and confirm that the board reads a sensible pipe temperature in both cooling and heating where possible.

Does a P2 repair involve refrigerant?

Normally, no. The sensor clips to the outside of the copper pipe, so the refrigerant circuit stays sealed. That keeps the repair simpler and cheaper than many other faults. However, if the technician finds signs of low refrigerant or a leak while testing, they will explain that separately. Our gas and regas page covers refrigerant repairs.

How does P2 relate to P8 and P9?

These three codes involve the indoor coil and are easy to confuse.

Mitsubishi Electric indoor coil related codes
CodeUsual meaning
P2Liquid pipe sensor reading is invalid
P9Coil sensor reading is invalid
P8Pipe temperature is valid but not changing as expected

So, P2 and P9 mean a sensor has failed, while P8 means the readings are believable but the coil is not performing. A drifting P2 sensor can sometimes cause a P8 first. Our P9 guide explains the other coil sensor.

Can P2 lead to ice or leaks?

It can. If the pipe sensor drifts before failing, the system may not protect the coil from freezing properly. Ice then forms, and when it melts, water may spill from the drain tray. If you have seen ice or drips as well as P2, mention both. Our guide on a Mitsubishi Electric freezing up explains other causes of ice.

Why does P2 sometimes follow a coil clean?

A thorough coil clean involves sprays, rinsing and moving parts around inside the unit. If the sensor lead gets wet, pulled or pinched, P2 can follow within days. Equally, a sensor clip knocked loose during the clean can let the sensor slide away from the pipe. If P2 appeared soon after a clean, contact whoever did the work. Often the fix is simply refitting the sensor, which takes very little time once the panels are off.

Do multi head systems behave differently?

Each indoor unit on a multi head system has its own pipe sensor and board, even though they share one outdoor unit and one compressor. So, P2 usually affects only the unit showing the code, while the others keep running. Note which room is affected and its model number when you book.

Can a ducted unit show P2?

Yes. Ducted and bulkhead units use the same kind of sensors inside their fan coils. Because the fan coil hides in the roof or under the floor, access takes longer. Mention where the access hatch is when booking. Our ducted page explains how ducted systems differ.

Why is the liquid pipe such a harsh place for a sensor?

In cooling, the liquid line carries refrigerant that is cooler than the room, so the pipe sweats with condensation. In heating, the same pipe can run warm. Over a year, the sensor sees thousands of swings between cold and damp and warm and dry. On top of that, the indoor fan creates constant vibration.

Mitsubishi Electric designs its sensors for these conditions, and many last for a very long time. Still, after enough years, the protective coating can crack or the lead can harden. Once moisture finds a way in, the reading becomes unreliable. That is why P2 tends to appear on older systems more than new ones.

Could a refrigerant problem show as P2?

Not directly. A refrigerant problem changes the real pipe temperature, but the sensor still reads it correctly, so the board would more likely show P8 or a protection code. P2 is specifically about the sensor reading being impossible. That said, a technician who has the gauges out may notice low pressures while testing and will tell you if they do.

What happens if the wrong sensor is fitted?

Different models use thermistors with different resistance curves, lead lengths and plugs. A sensor that looks similar but uses the wrong curve will give a believable yet wrong reading. The system might then run poorly without showing any code. For that reason, the technician matches the part to your exact model rather than grabbing a generic sensor.

Is it safe to keep using the system?

The unit usually stops itself, so normal use is not possible. If the fault comes and goes, the unit may run between faults with weaker protection against freezing. It is better to arrange the repair than rely on restarts.

How can you help prevent P2?

Sensors age regardless of how well you treat them, but a few habits help them last and help catch problems early.

  • Keep the filters clean so the coil does not freeze and soak the sensor.
  • Fix drain leaks quickly so water does not reach the board.
  • Choose a careful, licensed technician for coil cleans.
  • Book regular servicing, so a technician can compare sensor readings with a thermometer.

Our service page explains what a service includes.

What is the difference between a faulty sensor and a faulty board?

Both can show P2, so the technician separates them carefully. If the sensor measures correctly on the meter but the board still reports P2, the board input is the likely culprit. If the sensor reads far outside its chart, the sensor is to blame. Doing this test first avoids replacing an expensive board when a cheap sensor is the real problem.

How long does the repair take?

Once the part is on hand, a sensor replacement is usually one of the quicker jobs an air conditioning technician does. Access is the main variable. A wall split often opens quickly, while a ceiling cassette or a ducted unit may take longer. If the sensor needs ordering, the technician may need to return.

What helps when you book?

These simple notes make the visit smoother and may save a second trip.

  • The indoor model number from the unit label.
  • Whether P2 appears on a controller or as lamp blinks.
  • Any recent coil cleans, repairs or water leaks.
  • Whether ice has formed on the indoor coil.
  • How often the code comes and goes.

The short version on the Mitsubishi Electric P2 error

The Mitsubishi Electric P2 error means the indoor liquid pipe sensor is no longer giving a valid reading. Moisture, a slipped sensor, a damaged lead or a corroded plug is usually responsible, and the fix rarely touches the refrigerant. Without that reading, the system loses part of its coil protection.

After a single restart, book a Mitsubishi Electric technician to test and replace the sensor so your system runs safely again.

Frequently asked questions

What does P2 mean on a Mitsubishi Electric air conditioner?

P2 usually means the indoor liquid pipe temperature sensor has failed or its connection has a fault.

Does fixing P2 involve refrigerant?

Normally not. The sensor clips onto the outside of the pipe, so the refrigerant circuit stays sealed.

Why did P2 appear after a coil clean?

Cleaning can disturb the sensor lead or clip. Refitting the sensor often solves it.

How is P2 different from P8?

P2 means the sensor reading is invalid. P8 means the readings are valid but the coil is not changing temperature as expected.

Can P2 cause ice on the coil?

A drifting pipe sensor can weaken freeze protection, so ice may form before the code appears.

Can I keep using the system with P2?

The unit usually stops itself. It is better to arrange the repair than rely on restarts.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://mitsubishi.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, Mitsubishi Electric Service”,”url”:”https://mitsubishi.sydneyaircare.com.au/”,”description”:”Mitsubishi Electric air conditioner repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with Mitsubishi Electric.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”What does P2 mean on a Mitsubishi Electric air conditioner?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”P2 usually means the indoor liquid pipe temperature sensor has failed or its connection has a fault.”}},{“@type”:”Question”,”name”:”Does fixing P2 involve refrigerant?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Normally not. The sensor clips onto the outside of the pipe, so the refrigerant circuit stays sealed.”}},{“@type”:”Question”,”name”:”Why did P2 appear after a coil clean?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Cleaning can disturb the sensor lead or clip. Refitting the sensor often solves it.”}},{“@type”:”Question”,”name”:”How is P2 different from P8?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”P2 means the sensor reading is invalid. P8 means the readings are valid but the coil is not changing temperature as expected.”}},{“@type”:”Question”,”name”:”Can P2 cause ice on the coil?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”A drifting pipe sensor can weaken freeze protection, so ice may form before the code appears.”}},{“@type”:”Question”,”name”:”Can I keep using the system with P2?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”The unit usually stops itself. It is better to arrange the repair than rely on restarts.”}}]}
Call 02 9071 1142