Mitsubishi Electric E6 Error, Indoor to Outdoor Signal Fault
A Mitsubishi Electric E6 error tells you the indoor unit and the outdoor unit have lost their conversation.
Every split system relies on a steady stream of signals between its two halves, so when that link breaks, the system shuts down. Here is what E6 means, why it happens and how it gets sorted.
What is the Mitsubishi Electric E6 error?
Your split system has two circuit boards, one inside and one outside. While the system runs, they swap information constantly. The indoor board asks for cooling or heating, and the outdoor board reports back on the compressor, the fan and the temperatures it measures.
On many Mitsubishi Electric systems with a wired controller, E6 appears when that exchange fails. Service information usually describes it as an indoor and outdoor unit communication error. On wall splits without a code display, the same fault often shows as a set pattern of blinks on the operation lamp. Either way, the underlying message is exactly the same. The two units can no longer hear each other.
Why the system stops
Without a reliable link, the indoor unit cannot tell whether the compressor is running safely, and the outdoor unit does not know what the room needs. Running blind could freeze a coil or overheat the compressor. So the system stops and waits for the link to return. It may try again after a short pause, which is why some owners hear the unit click on and off before the code settles.
When do people usually see E6?
The code tends to show up in a handful of situations.
- Straight after a thunderstorm, a blackout or a flickering supply.
- On a brand new installation, often within the first few days.
- After building, roofing or garden work near the connecting cable.
- On older systems where terminals have loosened over many years.
- In coastal homes, after wet and windy weather.
Spotting which of these fits your situation helps narrow down the cause long before anyone opens a panel. For example, an E6 that starts the morning after a storm points one way, while an E6 that started the week after new guttering went up points another.
What causes the E6 code?
Most E6 faults trace back to the cable that joins the units, the power that feeds them or one of the two boards.
The interconnecting cable
A single multi core cable usually links the indoor and outdoor units. It carries both power and the signal on many models. If a core breaks, a joiner corrodes or someone nicks the cable with a spade or a saw, the signal drops out.
Loose or burnt terminals
Each end of that cable screws into a terminal block. Heating and cooling cycles can loosen the screws over time. A loose screw then heats up, and the terminal may scorch. The result is an unreliable signal that comes and goes.
Wiring mistakes during installation
On a new system, the cable cores must land on matching terminals at both ends. If two cores swap places, the units may power up but fail to talk. That is one reason E6 often appears soon after an installation.
Power supply problems
Low voltage, a failing isolator or a loose connection at the switchboard can upset communication. Storms and surges can also scramble the signal circuits on either board.
A faulty indoor or outdoor board
The communication circuits live on the circuit boards. A surge, moisture or age can damage them. In that case, the cable may test perfectly, yet the code keeps returning.
Interference and pests
Occasionally, the signal suffers interference from other cables run tightly alongside it. In addition, rodents and insects sometimes chew cables or nest around terminals inside the outdoor unit.
What can you safely check yourself?
Most of the fix sits inside the casings, so your role is to try a clean restart and gather clues.
- Turn the system off with the remote or wall controller.
- Switch off the circuit breaker for the air conditioner and the isolator beside the outdoor unit.
- Wait at least five minutes so the boards fully power down.
- Switch the breaker and isolator back on, then start the system again.
- Walk the visible route of the cable and look for cuts, crushed sections or chewed insulation, without touching it.
- Note when E6 appears and anything that happened just before.
Our guide on how to reset a Mitsubishi Electric air conditioner walks through the restart safely.
On many models the cable between the units carries mains voltage. Never cut, join or reconnect it yourself, and never open a terminal cover. Leave that to a licensed technician.
How does a technician track down E6?
A good technician works from the simplest explanation to the most complex.
Confirming the code and history
First, they confirm the code on the controller or by reading the blink pattern. Some systems also store recent faults, which can show whether E6 has happened before.
Checking supply voltage
Next, they measure the supply at the outdoor unit and at the indoor terminals. A weak or unstable supply can explain communication faults on its own.
Testing the cable
After that, they isolate the power and test each core of the cable for continuity and insulation. A damaged core, a short between cores or a short to earth all show up clearly.
Inspecting terminals
They also open the terminal covers and look for loose screws, scorch marks, corrosion or insects. Tightening or replacing a damaged terminal often clears the fault completely.
Measuring the signal
Finally, if the cable and supply look healthy, they measure the signal at each board while the system runs. A missing or distorted signal points to whichever board is failing.
Can E6 be repaired quickly?
Often, yes. A loose terminal, a damaged section of cable or a wiring mix up on a new install are usually straightforward fixes. On the other hand, a failed board takes longer, because the technician has to order the correct part for your model.
If the cable runs through a wall or roof space and has suffered damage out of sight, replacing the whole run may be the neater option. The technician will explain the choices before starting. Our repair page explains how repair decisions work.
How does E6 compare with nearby codes?
Mitsubishi Electric uses several codes that can sound alike. This table shows where E6 sits.
| Code | What it usually points to |
|---|---|
| E6 | Indoor and outdoor units have lost communication |
| U9 | Outdoor unit supply voltage problem |
| U6 | Compressor overcurrent or power module fault |
| P8 | Pipe temperature not changing as expected |
If you have seen U9 as well, mention it, because supply problems often sit behind both. Our error codes guide covers the full list.
Why does E6 show up after storms?
Thunderstorms send surges through power lines and sometimes through the ground. The communication circuits on air conditioner boards are sensitive, so a surge can upset them or damage small parts. Brief blackouts can also leave the two boards out of step.
In many cases, a full power restart clears a storm related E6. However, if the code keeps coming back after a storm, one of the boards may have suffered damage, and a technician needs to test it.
Why does E6 appear on new installations?
New systems sometimes show E6 within days. The most common reasons are cores landed on the wrong terminals, a loose screw, a cable that is too light for the run or a join made inside a wall. If your system is new, contact the installer first, because the fix may fall under their workmanship. Our installation page covers what a good installation includes.
Does E6 affect multi head systems differently?
On a multi head system, one outdoor unit serves several indoor units, each with its own cable. If only one indoor unit shows E6, the problem usually sits with that unit or its cable. If every indoor unit shows the code together, the outdoor board or the main supply becomes the likely suspect. Noting which units stopped saves time on the day.
What if the code clears and returns?
An intermittent E6 is common, and it often points to a terminal or joint that makes contact only some of the time. Heat, vibration and moisture can all change that contact. As a result, the system may run fine for days, then stop again on a hot afternoon or after rain.
Keep a simple log of when the code appears, the weather and the mode. That record gives the technician a pattern to work with, especially if the fault refuses to show during the visit.
How long can a cable fault stay hidden?
Surprisingly long. A cable may suffer a small nick during a renovation, then work perfectly for months. Over time, moisture creeps into the damaged spot and corrosion builds up. Eventually, the signal weakens enough to trip E6, often long after anyone remembers the original work.
For this reason, technicians test the full length of the cable rather than only the ends. If part of the run sits inside a wall or roof space, they may compare readings from each end to judge where the damage lies. Sometimes a fresh cable run proves quicker and more reliable than chasing a hidden fault.
Can the wall controller cause E6?
Rarely. The wired controller talks to the indoor unit, not directly to the outdoor unit, so a controller fault usually shows a different code or a blank screen. Still, a damaged controller cable can create confusing symptoms. If your controller flickers, resets itself or shows odd text alongside E6, mention it when you book.
How can you lower the risk of E6?
You cannot prevent every electrical fault, but some habits help.
- Keep garden tools, edgers and spades away from the cable route.
- Make sure trades working on the roof or walls know where the cable runs.
- Keep the outdoor unit clear of nests and ant trails.
- Consider surge protection for the home, discussed with a licensed electrician.
- Book regular servicing so a technician can check and tighten terminals.
Our service page explains what a service includes.
Is it safe to keep resetting the system?
One restart is perfectly fine. Repeated restarts rarely fix a genuine wiring or board fault, and they can stress parts that are already struggling. If E6 returns after a clean restart, leave the system off and arrange a check.
What details help when you book?
Have these details ready when you call us.
- The model numbers from the indoor and outdoor unit labels.
- Whether the code shows on a wall controller or as lamp blinks.
- When E6 first appeared, and whether it comes and goes.
- Any storms, outages, renovations or garden work beforehand.
- Whether you have one indoor unit or several.
Final thoughts on the Mitsubishi Electric E6 error
The Mitsubishi Electric E6 error means the two halves of your system have stopped communicating. Damaged cables, loose terminals, wiring mistakes, power problems and board faults are the usual culprits. A clean restart is worth one try, along with a visual check of the cable route.
If the code comes back, book a Mitsubishi Electric technician to test the cable, the supply and both boards properly.
Frequently asked questions
What does E6 mean on a Mitsubishi Electric air conditioner?
E6 usually means the indoor and outdoor units have lost communication, so the system stops to protect itself.
Can a storm cause a Mitsubishi Electric E6 error?
Yes. Surges and blackouts can upset or damage the communication circuits. A clean restart sometimes clears it.
Why did E6 appear on my new system?
New installs can show E6 if cable cores land on the wrong terminals, a screw is loose or the cable is unsuitable. Contact the installer first.
Can I fix the connecting cable myself?
No. On many models it carries mains voltage. A licensed technician should test and repair it.
Does E6 mean a new circuit board?
Not always. Cables, terminals and supply problems cause many E6 faults. A technician replaces a board only after testing.
Why do all my indoor units show E6 together?
On multi head systems, that pattern points to the outdoor board or the main supply rather than one indoor unit.