Mitsubishi Electric U6 Error, Compressor Drawing Too Much Current
Picture the compressor as the heart of your air conditioner and the inverter as the nerve that tells it how hard to beat.
A Mitsubishi Electric U6 error means that nerve detected a dangerous surge of current, either in the compressor or in the power module feeding it. The system stops instantly to prevent damage. Here is what lies behind it.
Making sense of the Mitsubishi Electric U6 code
Inverter driven compressors do not simply switch on and off. Instead, a power module on the outdoor board chops and shapes electricity to spin the compressor motor at exactly the speed needed. Along the way, the board measures the current flowing out to the motor many times every second.
When that current leaps far above normal, the board shuts down immediately and records U6. Mitsubishi Electric service information commonly links U6 to compressor overcurrent or a power module abnormality. In plainer words, either the compressor demanded far too much power, or the part supplying that power misbehaved.
Why the cut off is so abrupt
Power modules can be destroyed in a fraction of a second by extreme current. Windings inside the compressor can overheat just as quickly. So, the protection does not wait. That speed explains why owners often hear the outdoor unit start, then stop with a thud almost straight away. The board may try again after a pause, which is why some people hear several starts and stops before the code settles.
Patterns owners commonly report
U6 tends to arrive in one of a few recognisable ways, and each hints at a different cause.
- The compressor tries to start, thumps, then falls silent within seconds.
- The system runs for a while, then trips during the hottest part of the day.
- Each restart ends the same way, sometimes faster each time.
- A circuit breaker trips occasionally along with the code.
- Other outdoor codes, such as U5, showed up in previous weeks.
Paying attention to whether U6 strikes at start up or after running is one of the most useful observations you can share. Listen near the outdoor unit when you switch on, from a safe distance, and note whether you hear a normal hum, a thump or nothing at all.
What drives a U6 surge?
The fault can begin in the compressor, in the wiring, on the board or in the conditions the system is working against.
Compressor winding breakdown
Copper windings inside the compressor are protected by thin insulation. Years of heat can weaken it. Once a winding shorts to its neighbour or to the casing, current spikes and U6 trips. Nobody can repair a shorted winding inside the sealed shell, so a compressor with this fault needs replacing.
A compressor that is stiff to turn
Wear, lost lubrication or liquid refrigerant collected inside the shell can make the compressor hard to start. The inverter then pushes far more current than usual to get it moving.
Burnt or loose terminals
Three heavy wires link the power module to the compressor. A loose screw or a corroded terminal creates resistance, heat and arcing. Arcing produces sharp current spikes that look exactly like overcurrent to the board.
Power module failure
The power module itself can fail through age, heat or surge damage. A partially failed module may short internally and send a burst of current. In that case, the board or module needs replacing.
High system pressure
A choked outdoor coil, a slow fan or an overcharged system all raise pressure. Higher pressure makes every revolution of the compressor harder, which pushes current up. Very high pressure may also show as U1.
Overheated electronics
A module that has been running hot, perhaps after repeated U5 events, becomes more fragile and more likely to trip on current.
Steps that are safe for you
There is very little you can test yourself, but you can avoid making things worse and gather information that helps the technician diagnose the fault faster.
- Switch the system off and leave it for at least fifteen minutes.
- Turn off the breaker, wait a few minutes, then turn it back on.
- With the isolator off, clear any debris around the outdoor unit.
- Sniff for burning and look for scorch marks or smoke stains on the casing. If you find any, leave everything off.
- Restart once, listening for whether the compressor starts before the fault.
- If U6 returns, leave the system off and book a check.
Our guide on how to reset a Mitsubishi Electric air conditioner explains the restart.
If you notice a burning smell or see scorch marks, switch off at the switchboard, keep everyone away from the outdoor unit and call a licensed technician. Do not try to restart.
How technicians investigate U6
The aim is to separate a compressor problem from a board problem, because the costs differ enormously. A careful step by step approach avoids replacing an expensive compressor when the real fault was a burnt terminal or a tired module.
Safe isolation
The technician switches off, waits for stored charge to drain and opens the electrical compartment.
Terminal inspection
They inspect the compressor terminals and power module connections for discolouration, looseness and corrosion. Burnt terminals often explain U6 straight away.
Winding tests
They measure resistance between each pair of compressor windings and between each winding and the casing. Unequal values or a path to the casing indicate a damaged compressor.
Module output test
If the compressor passes, they check the power module output, often with a dedicated tester that stands in for the compressor. A faulty module reveals itself clearly.
System conditions
Finally, they check pressures, airflow and refrigerant charge, because high load can trigger U6 even with healthy parts.
What repairs look like
The fix depends entirely on what testing reveals, so expect the technician to explain the findings before quoting.
- Terminal and wiring faults are usually modest repairs.
- A failed power module or board means a replacement part for your model.
- High pressure caused by dirt or overcharge means cleaning or correcting the charge.
- A damaged compressor means refrigerant recovery, brazing in a new compressor, pressure testing, evacuation and recharging.
Because a compressor replacement is a major job, it is worth comparing that cost with a new system on older units. Our repair page explains how to weigh the options.
How U6 compares with other codes
| Code | Typical meaning |
|---|---|
| U6 | Compressor overcurrent or power module abnormality |
| U5 | Heat sink running too hot |
| U9 | Supply voltage problem at the outdoor unit |
| U1 | Abnormally high refrigerant pressure |
If U9 appears as well, a poor supply may be contributing. Voltage dips can make the compressor draw more current.
Start up faults versus running faults
When U6 hits within seconds of starting, the technician thinks first about winding damage, a seized or stiff compressor, liquid in the shell or a weak module. Starting is the most demanding moment, so marginal parts tend to fail there.
When U6 appears after the system has run for a while, heat is often involved. Windings expand as they warm and weak insulation can break down, while a module with poor thermal contact can trip once it heats up. High afternoon pressures also push current gradually higher.
When the compressor needs replacing
A compressor swap is a significant undertaking. The technician recovers all refrigerant, cuts out the old compressor, brazes in the new one along with a fresh filter drier, proves the joints with nitrogen, evacuates the system to remove moisture and recharges by weight. They then test under load. Because this takes time and parts, it suits younger systems best. On an older system with other worn parts, putting that money towards a new, more efficient system often makes more sense, and the technician can talk through the figures with you honestly.
Liquid in the compressor, explained
When a system sits idle for a long time, especially through a cold spell, refrigerant can migrate and settle as liquid inside the compressor shell. Compressors are built to squeeze gas, not liquid. When the motor tries to start against a pool of liquid, the effort spikes and current jumps.
Many outdoor units include features that warm the compressor or manage start up to prevent this. Still, if U6 tends to appear after the system has been off for weeks, mention it. The technician may look closely at those start up protections and at the refrigerant charge, since an overcharge makes liquid build up more likely.
How electricity quality plays a part
The inverter needs a steady supply to work smoothly. When voltage sags, the board compensates by drawing more current for the same work, and that extra current narrows the safety margin. Loose connections at the isolator or switchboard can cause local sags every time the compressor starts.
That is why the technician may measure supply voltage at the outdoor unit while the compressor starts. If it dips sharply, a licensed electrician may need to check the circuit, the cable size or the connections before the air conditioner repair can succeed.
What a terminal fault looks like up close
Burnt terminals are often easy to spot once the panel is off. The plastic around them may be brown or melted, the metal may look blackened and there may be a sharp electrical smell. Sometimes the wire insulation nearby has hardened or cracked. Replacing damaged terminals and leads is far cheaper than replacing a compressor, so this inspection matters.
Could a storm be to blame?
Storms rarely damage a compressor directly, but they can weaken a power module, which may then fail days or weeks later with U6. If the trouble started soon after a storm or blackout, mention it so the technician looks for surge damage.
Should you keep trying to restart?
No. Each attempt drives heavy current through parts that may already be damaged. A loose terminal can become a burnt board, and a weak winding can become a dead compressor. One restart to rule out a glitch is enough.
Ways to reduce the risk of U6
- Keep the outdoor coil clean and the area around it open.
- Avoid switching the system on and off rapidly.
- Rinse salt from coastal outdoor units now and then, isolator off.
- Use licensed technicians so refrigerant charge stays correct.
- Book servicing that includes terminal checks and current readings.
Our service page explains what a service includes.
Does U6 affect every indoor unit?
On a multi head system, every indoor unit depends on the one outdoor compressor, so U6 stops them all together. On a single split, only that room loses cooling or heating. That shared stop is itself a useful clue that the fault lives outside.
What to share with us
- Model numbers from the indoor and outdoor units.
- Whether U6 strikes at start up or after running.
- Any burning smell, breaker trips or storms.
- Any earlier codes such as U5, U1 or U9.
- How old the system is, if you know.
Bringing it together on the Mitsubishi Electric U6 error
The Mitsubishi Electric U6 error tells you the inverter detected a dangerous surge of current in the compressor circuit. Burnt terminals, a failing power module, high system pressure or a damaged compressor can be responsible. Try one restart at most, and stop immediately if you smell burning.
Then book a Mitsubishi Electric technician to test the compressor, terminals and module and give you clear options.
Frequently asked questions
What does U6 mean on a Mitsubishi Electric air conditioner?
U6 usually means compressor overcurrent or a problem with the power module that drives the compressor.
Does U6 mean the compressor is dead?
Not necessarily. Burnt terminals, a faulty power module or high pressure can cause U6. Testing separates these.
Can I keep restarting the system after U6?
No. One restart is enough. Repeated attempts can damage the module or compressor further.
Why does U6 happen at start up?
Starting is the most demanding moment, so a weak compressor, liquid in the shell or a tired module often fails then.
Can a dirty outdoor unit contribute to U6?
Yes. High pressure from a dirty coil makes the compressor harder to turn, which raises current.
What should I do if I smell burning?
Switch off at the switchboard, keep away from the outdoor unit and call a licensed technician.