Mitsubishi Electric P5 Error, Drain Pump Not Coping

Inside many ceiling cassettes and ducted units, a little pump works hard every summer lifting condensation up and out of the ceiling.

The Mitsubishi Electric P5 error says that pump has failed or cannot keep pace. This guide explains how the pump works, why it gives up and what a technician will do.

What is the Mitsubishi Electric P5 error?

Air conditioners pull moisture out of the air as they cool. In a ceiling mounted unit, that water collects in a tray that often sits lower than the drain outlet. A small electric pump solves the problem by lifting the water up to a point where it can flow away by gravity.

On many Mitsubishi Electric models, service information associates P5 with the drain pump. The board may raise it when the pump does not draw current as expected, when water stays high despite the pump running or when a related protection trips. In plain language, water is not leaving the unit the way it should, and the pump is the prime suspect. The board stops cooling so that no more water is produced until the problem is fixed, which protects your ceiling.

Which units have a drain pump?

Drain pumps are standard in most ceiling cassettes and are common in bulkhead, concealed ducted and some floor or ceiling suspended units. Ordinary high wall splits usually drain by gravity, so they rarely show P5.

Telltale signs of a struggling pump

Before or alongside the code, you might notice some of the following.

  • A pump that hums loudly or rattles from inside the ceiling.
  • Total silence from the pump during cooling on a humid day.
  • Water marks or drips around a cassette grille.
  • Cooling stopping after an hour or two on muggy afternoons.
  • A sour or swampy smell near the outlets.

If water is coming through the ceiling, switch the system off immediately and move anything valuable out of the way.

Why do drain pumps fail?

Pumps are small, hard working and live in a wet, dirty environment. That combination wears them out.

Slime around the impeller

The impeller is the little spinning part that pushes water. Slime and sludge from the tray wrap around it and choke the inlet. The motor still turns, yet very little water moves. This is by far the most common pump problem, and the cheapest to fix.

Worn motor

After many seasons, the pump motor itself can fail. Bearings wear, windings overheat and the pump either stops or turns too slowly.

Too much lift

Every pump has a maximum height it can lift water. If the drain line rises higher than that, perhaps after a ceiling change, the pump cannot keep up. Long, narrow or kinked lines add extra resistance.

Air locks and back flow

If the drain line dips and rises again, air can trap in the high spots and water can run back into the tray when the pump stops. The pump then works far harder than it should.

Electrical faults

A loose plug, a corroded terminal or a fault on the board output can starve the pump of power. In that case, replacing the pump alone would not fix anything, so the technician checks the power reaching the pump before ordering parts.

What can you safely do?

Most of the drain system sits inside the ceiling, but you can still help in a few useful ways.

  1. Switch the system off at the controller.
  2. Put towels or a bucket under any drips and move furniture.
  3. Find the drain outlet outside and clear any soil, leaves or insects around it.
  4. Clean any filters you can reach safely, because frozen coils can release a sudden flood when they thaw.
  5. Leave the system off for a while, then try once and see whether P5 returns.

Our guide to a Mitsubishi Electric leaking water explains other water problems, and our filter cleaning guide shows safe filter care.

Water and electricity do not mix

If water drips near light fittings or ceiling fans, switch off those circuits at the switchboard and keep people away until the area dries and a licensed tradesperson checks it.

How does a technician repair P5?

A good repair fixes the pump and also the reason it struggled in the first place.

Inspecting the tray and pump

The technician isolates the power, opens the unit and looks at the water level, the slime build up and the pump inlet.

Cleaning first

They clear slime from the tray, the inlet screen and the impeller. Often, a thorough clean brings a sluggish pump back to full strength.

Testing flow

Next, they pour water into the tray and time how quickly the pump clears it. They also listen for unusual noise and check the current the pump draws.

Checking the drain route

They then follow the drain line, looking for excessive lift, sags, kinks, air locks and back flow. Correcting the route can be just as important as replacing the pump.

Replacing the pump

If the motor is worn or the pump will not reach its rated flow, they fit a replacement suited to the model. They then test the system under normal cooling to confirm that water leaves as fast as it forms.

How quickly should you act on P5?

Promptly, and certainly before the next humid day. A failed pump means water keeps accumulating while the system runs, and the safety switch is the only thing standing between that water and your ceiling. Leaving the system off until a technician has checked it is the safest approach.

How does P5 relate to P4?

These two codes often travel together.

Mitsubishi Electric drain codes
CodeUsual meaning
P5Drain pump fault or pump not clearing water
P4Float switch or drain sensor fault, or high water detected

In short, P4 is the water level warning, while P5 points more directly at the pump. Depending on the model and the fault, either code may appear first.

Why does P5 show up in summer?

The amount of water a unit produces depends on humidity. On a dry day, a tired pump may cope. On a sticky day, the flow can double, and the same pump falls behind. That is why many P5 faults appear during the first humid week of the season. A pump test before summer catches tired pumps early.

Do ducted units need special care?

Ducted fan coils often sit directly above bedrooms or living areas. If the pump fails, water can soak through the ceiling before anyone notices. Some installations include a secondary safety tray beneath the unit, which is worth checking during a service. Our ducted page explains ducted maintenance.

Can a renovation cause P5?

Yes. Electricians, plumbers and builders working in the ceiling sometimes move or crush drain lines to reach their own work. A line that now rises higher, dips or kinks can overload the pump. If P5 started after building work, mention it when booking.

Will the system heat with P5?

Usually, yes. In heating mode, the indoor coil runs warm, so it produces little or no water. Many systems therefore heat normally all winter, only to show P5 again in spring. Fixing the pump during the cooler months avoids a breakdown on the first hot day.

Is a pump replacement expensive?

Pumps are moderately priced parts, and the job does not involve refrigerant. Access is the biggest variable. A cassette in a standard ceiling is usually straightforward, while a ducted unit in a cramped roof space takes more time. Our pricing page explains what affects costs.

What does a technician mean by pump lift?

Lift is the vertical distance the pump has to raise water before gravity takes over. Each pump model has a maximum lift in its specifications, and good installations stay comfortably inside it. Push close to the limit, and the pump works at full effort every time, which shortens its life.

The horizontal run matters too. Long, narrow lines with many bends add friction, so the pump effectively has to work harder. A technician looks at both the height and the route when deciding whether a new pump will cope or whether the drain line also needs changing.

Can a drain line be redesigned?

Sometimes that is the best long term fix. If the original line climbs too high, dips and rises in the ceiling or runs to an awkward outlet, rerouting it can take a lot of strain off the pump. In some homes, a different outlet location lets gravity do more of the work. The technician can explain whether this is practical in your ceiling.

What about condensate pumps on wall splits?

Occasionally, a high wall split is installed where gravity drainage is not possible, such as on an internal wall. In that case, the installer may fit a small separate condensate pump, often hidden in the trunking or the wall. Those pumps do not always report to the indoor board, so they may fail silently and simply leak. If you have a pump on a wall split and see drips, mention the pump specifically.

Smells, slime and the drain tray

Still water in the tray breeds slime remarkably fast in warm weather. The slime then feeds back into the pump and the drain line. Regular tray cleaning and treatment with a suitable product during servicing helps break that cycle. Many owners find that the swampy smell from their cassette disappears once the tray is properly cleaned. Our guide on a Mitsubishi Electric AC that smells bad explains more about smells.

How long do drain pumps last?

It varies widely with water quality, cleaning habits and how hard the system works. Pumps that receive regular tray cleaning and live in a well designed drain route generally last longer, sometimes for many years. Pumps fighting slime and steep lifts every summer wear out faster.

How can you help the pump last?

  • Clean the filters often so the coil stays clean and does not freeze.
  • Ask for the tray to be cleaned and treated during each service.
  • Keep the outside outlet clear of soil and insects.
  • Mention smells and gurgling early.
  • Tell trades working in the ceiling where the drain line runs.

Our service page explains what a full service covers.

Should you run fan only mode instead?

Fan only mode moves air without cooling, so the coil makes no water and the pump has nothing to do. Some owners use it to keep air moving while they wait for the repair. That is generally fine, as long as the tray is not already overflowing. If water is still dripping, keep the unit off altogether until the technician arrives.

Details that help when you call

  • The unit type, such as cassette, ducted or bulkhead.
  • The model number from the unit or controller.
  • Whether you can hear the pump and what it sounds like.
  • Where water has appeared and how much.
  • Any recent building work in the ceiling.

The bottom line on the Mitsubishi Electric P5 error

The Mitsubishi Electric P5 error points to a drain pump that has failed or cannot keep up. Slime, wear, excessive lift, air locks and electrical faults are the usual causes. Switch off, protect the area below and clear the outside outlet if you can.

Then book a Mitsubishi Electric technician to clean or replace the pump and make sure the drain route lets it do its job.

Frequently asked questions

What does P5 mean on a Mitsubishi Electric air conditioner?

P5 usually points to the condensate drain pump, either a pump fault or the pump not clearing water fast enough.

Which units have a drain pump?

Most ceiling cassettes and many ducted, bulkhead and ceiling suspended units use a drain pump.

Can cleaning fix a P5 error?

Often. Slime around the pump inlet and impeller is a common cause, and a thorough clean can restore flow.

Why does P5 happen on humid days?

Humid air produces more water, and a tired pump may not keep up with the extra flow.

Does a pump replacement involve refrigerant?

No. The drain pump is part of the water side of the unit, so the refrigerant circuit stays sealed.

Will my system still heat with P5?

Usually, because heating produces little water. The fault often returns when cooling season starts.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://mitsubishi.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, Mitsubishi Electric Service”,”url”:”https://mitsubishi.sydneyaircare.com.au/”,”description”:”Mitsubishi Electric air conditioner repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with Mitsubishi Electric.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”What does P5 mean on a Mitsubishi Electric air conditioner?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”P5 usually points to the condensate drain pump, either a pump fault or the pump not clearing water fast enough.”}},{“@type”:”Question”,”name”:”Which units have a drain pump?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Most ceiling cassettes and many ducted, bulkhead and ceiling suspended units use a drain pump.”}},{“@type”:”Question”,”name”:”Can cleaning fix a P5 error?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Often. Slime around the pump inlet and impeller is a common cause, and a thorough clean can restore flow.”}},{“@type”:”Question”,”name”:”Why does P5 happen on humid days?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Humid air produces more water, and a tired pump may not keep up with the extra flow.”}},{“@type”:”Question”,”name”:”Does a pump replacement involve refrigerant?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”No. The drain pump is part of the water side of the unit, so the refrigerant circuit stays sealed.”}},{“@type”:”Question”,”name”:”Will my system still heat with P5?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Usually, because heating produces little water. The fault often returns when cooling season starts.”}}]}
Call 02 9071 1142