Mitsubishi Electric Air Conditioner Not Heating, Causes and Fixes

A Mitsubishi Electric air conditioner not heating on a cold Sydney morning leaves the whole house chilly.

Before assuming the worst, it helps to know which winter behaviours are normal, such as warm up delays and defrost pauses, and which point to a fault. This guide walks through both, from simple checks to the repairs a technician handles.

First, is it really a fault?

Heat pumps behave differently in winter, and several perfectly normal habits get mistaken for problems. Understanding them first can save you an unnecessary call out.

The warm up delay

When you switch on heating, the indoor fan often waits before blowing. The system is warming the indoor coil first so it does not blow cold air at you. Depending on conditions, this can take a few minutes, and longer on frosty mornings.

Defrost pauses

In heating, the outdoor coil gets colder than the outside air and collects frost. Every so often, the system pauses heating to melt it. During defrost, the indoor fan usually stops, the outdoor unit may hiss or whoosh and steam may rise from the outdoor coil. After a few minutes, heating resumes.

Gentle running near the set point

Once the room is close to the set temperature, an inverter system slows right down. The air may then feel only mildly warm. That is efficient, not faulty, and it saves power.

If your system shows these behaviours and then delivers warm air, it is probably healthy. If it never warms the room, keep reading. The next sections start with the simple checks anyone can do and work towards the faults that need specialist tools and a licence.

Check the settings

  • Confirm the mode is heat, often shown as a sun symbol, not cool, dry or fan.
  • Make sure the set temperature is higher than the current room temperature.
  • Choose a medium or higher fan speed while the room warms.
  • Point the vane downwards in heating, because warm air rises naturally.
  • Check timers and app schedules that might switch heating off.

Our guides to Mitsubishi Electric modes and timer settings cover these controls.

Filters matter even more in winter

In heating, the indoor coil releases heat into the room. If the filters clog, that heat cannot get out, so the coil overheats and the system cuts back or stops. Heating then feels weak and patchy.

  1. Switch the unit off.
  2. Lift the front panel and remove the filters.
  3. Rinse them with lukewarm water and let them dry in the shade.
  4. Refit them and restart.

Our guide to cleaning Mitsubishi Electric filters shows each step.

Look at the outdoor unit

The outdoor unit collects warmth from the outside air, even on cold days. To do that, it needs open airflow and a coil that is not buried in ice.

  • Turn off the isolator before inspecting the unit.
  • Clear leaves, plants and stored items from around it.
  • Check whether thick ice covers the coil for long periods.
  • Make sure water can drain away from the base.

A light frost that clears regularly is normal. Heavy ice that never clears is not, and it usually needs a technician. Ice that builds up in the base can also lift the unit slightly or damage the fan, so it is worth dealing with promptly. Our outdoor unit check explains safe steps.

Never chip away ice

Scraping or hacking at ice can puncture the coil and cause a refrigerant leak. Switch the system off and let the ice melt on its own.

Common faults behind poor heating

When the basics check out, the cause is usually one of these faults, each of which needs a technician to confirm and fix.

Low refrigerant

A slow leak reduces heating capacity just as it reduces cooling. Many owners first notice it in winter, when the system struggles on cold mornings. Codes such as U2 can appear.

Defrost problems

If defrost runs too often, the room keeps cooling down. If it runs too rarely, ice chokes the outdoor coil. Faulty outdoor sensors, shown by codes such as U4, are a common cause.

The reversing valve

Every heat pump has a valve that switches refrigerant flow between cooling and heating. If it sticks, the system may cool when you ask for heat, or deliver little heat at all. Sometimes the valve sticks only now and then, so heating works one day and fails the next, which can be confusing for owners and technicians alike.

Indoor coil sensor faults

The sensor on the indoor coil decides when the fan starts in heating. A faulty sensor, often shown as P9, can make the fan start too early with cold air or never start at all.

Outdoor fan or compressor faults

Without the outdoor fan, the outdoor coil cannot collect heat. A failing compressor cannot build pressure. Codes such as U8 or U6 may appear.

Why cold mornings are the hardest test

Heat pumps work by collecting warmth from outdoor air, and the colder that air, the harder the job becomes. On frosty mornings, the system also needs more defrost cycles. As a result, a system with a minor fault may cope on mild winter days but struggle badly at dawn on the coldest days.

If your heating problems cluster around cold mornings, mention it. It helps the technician focus on defrost, refrigerant charge and outdoor coil performance.

Rooms that never get warm

Sometimes the system heats well, yet one room stays cold. Several reasons are common.

  • The room is larger than the system was sized for.
  • Doors are open to colder parts of the house.
  • Poor insulation or large windows lose heat quickly.
  • On ducted systems, a zone is closed or a duct has come loose.

Draught proofing, curtains and keeping doors closed can make a real difference, often more than people expect. For ducted systems, our ducted page explains zones and ducts.

Where you mount the unit changes how heat feels

Warm air rises. A wall unit mounted high near the ceiling can leave warm air pooling up top while your feet stay cold, particularly in rooms with high ceilings. Pointing the vane down and running a ceiling fan on its winter setting, if it has one, pushes that warmth back towards the floor.

Floor console units, by contrast, release warm air low down, which many people find more comfortable for heating. If heating comfort has always disappointed in a particular room, the type and position of the indoor unit may be part of the story rather than a fault.

The role of the outdoor temperature

Heat pumps lose some capacity as outdoor temperatures fall. Mitsubishi Electric designs many of its systems to keep heating well in cold conditions, but every heat pump works harder when the air outside is near freezing. Sydney rarely sees extreme cold, yet frosty western suburbs and elevated areas can still challenge an older or undersized system at dawn.

If heating only disappoints on the very coldest mornings and is fine the rest of the time, the system may be working within its limits. Running it a little earlier, before everyone wakes, can help the house reach a comfortable temperature in time.

Electricity costs and heating

Many households turn to their heat pump in winter because it usually heats more efficiently than plug in electric heaters. Still, running costs rise when filters are dirty, the outdoor coil is iced or the system works against open doors and draughts. Keeping the system clean and the house sealed improves both comfort and efficiency.

A heating checklist for the start of winter

  • Wash the indoor filters before the first cold snap.
  • Switch heating on for a test run on a mild day to confirm it works.
  • Clear leaves and garden growth from around the outdoor unit.
  • Check that the base of the outdoor unit can drain melt water.
  • Book a service if the system struggled last winter.

Doing these checks early avoids discovering a fault on the first freezing morning.

When warm air turns cold mid cycle

If warm air suddenly turns cool for a few minutes before returning, the system is probably defrosting. That is normal. However, if the cool spells happen very often or last a long time, defrost control may be faulty. Note how often it happens and for how long.

Can a remote or controller cause heating problems?

Yes, more often than people think. A remote with weak batteries may send only part of a command, so the unit changes temperature but not mode, or the other way round. A wall controller set to the wrong mode by another family member can also leave the system cooling quietly in winter. Check the display carefully, replace remote batteries if the screen looks faint, and confirm that the unit beeps when you send a command. Our guide on a Mitsubishi Electric remote not working covers remote problems.

What if the system heats, then switches off?

A system that heats for a while and then stops may be tripping a protection. In heating, dusty filters can make the indoor coil overheat, which triggers P6. Alternatively, a timer may be switching it off at a set time. Check for codes and timers first. If the system keeps stopping without an obvious reason, our guide on a Mitsubishi Electric turning off by itself explains other causes.

Heating in a multi head system

When several indoor units share one outdoor unit, they generally all need to run in the same broad mode. If one unit is set to cool while another asks for heat, the system cannot do both, and one room may get nothing useful. Make sure every indoor unit on the system is set to heat during winter. This simple conflict catches out many households.

When to call a technician

Book a visit if any of these situations apply to your system this winter.

  • The system never delivers warm air after the warm up period.
  • Thick ice stays on the outdoor coil for long periods.
  • Cool air blows in heating mode most of the time.
  • Codes keep returning after a restart.
  • Heating has weakened noticeably compared with previous winters.

Our repair page explains how a repair visit works.

What happens during the visit

The technician checks settings and filters first, then measures the air temperature at the outlet. Next, they inspect the outdoor unit, watch a defrost cycle where possible and measure pressures and temperatures. They also test the reversing valve operation and key sensors. From those results, they can tell whether the issue lies with refrigerant, defrost control, sensors, valves or the compressor.

Keeping heating reliable through winter

  • Wash filters before winter and every few weeks during heavy use.
  • Keep the outdoor unit clear and make sure its base drains freely.
  • Book a pre winter service so defrost and heating performance get checked.
  • Point the vane downwards in heating for better comfort.
  • Act early when heating starts to feel weaker than usual.

Our service page explains what a service covers.

Final thoughts on a Mitsubishi Electric air conditioner not heating

A Mitsubishi Electric air conditioner not heating may simply be warming up or defrosting, so give it a few minutes before worrying. If it never warms the room, check the mode, the set temperature, the filters and the outdoor unit. Those steps solve many cases.

If heating stays weak, book a Mitsubishi Electric technician to check refrigerant, defrost control and sensors.

Frequently asked questions

Why does my Mitsubishi Electric take a while to blow warm air?

In heating, the fan waits until the indoor coil is warm so it does not blow cold air. This delay is normal.

Why does my heat pump stop heating for a few minutes?

It is probably defrosting the outdoor coil. Heating resumes once the frost melts.

Is steam from the outdoor unit normal in winter?

Yes. Steam often rises from the outdoor coil during defrost.

Can dirty filters stop heating?

Yes. In heating, clogged filters trap heat in the indoor coil, so the system cuts back or stops.

Why is there thick ice on my outdoor unit?

Heavy ice that never clears can mean a defrost fault, low refrigerant or a drainage problem. A technician should check it.

Why does my system blow cold air in heat mode?

It may be defrosting, or a faulty coil sensor or reversing valve may be involved. Persistent cold air needs a check.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://mitsubishi.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, Mitsubishi Electric Service”,”url”:”https://mitsubishi.sydneyaircare.com.au/”,”description”:”Mitsubishi Electric air conditioner repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with Mitsubishi Electric.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”Why does my Mitsubishi Electric take a while to blow warm air?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”In heating, the fan waits until the indoor coil is warm so it does not blow cold air. This delay is normal.”}},{“@type”:”Question”,”name”:”Why does my heat pump stop heating for a few minutes?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”It is probably defrosting the outdoor coil. Heating resumes once the frost melts.”}},{“@type”:”Question”,”name”:”Is steam from the outdoor unit normal in winter?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. Steam often rises from the outdoor coil during defrost.”}},{“@type”:”Question”,”name”:”Can dirty filters stop heating?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. In heating, clogged filters trap heat in the indoor coil, so the system cuts back or stops.”}},{“@type”:”Question”,”name”:”Why is there thick ice on my outdoor unit?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Heavy ice that never clears can mean a defrost fault, low refrigerant or a drainage problem. A technician should check it.”}},{“@type”:”Question”,”name”:”Why does my system blow cold air in heat mode?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”It may be defrosting, or a faulty coil sensor or reversing valve may be involved. Persistent cold air needs a check.”}}]}
Call 02 9071 1142