How to Reset Mitsubishi Electric Air Conditioner Units Safely
Knowing how to reset Mitsubishi Electric air conditioner units is handy after a storm, a blackout or a puzzling glitch.
A proper reset gives the electronics a clean start and often clears temporary faults. However, it cannot fix a broken part. This guide explains the safe ways to reset, what each one does and when to stop and call for help.
What a reset actually does
Your air conditioner is controlled by circuit boards in both the indoor and outdoor units. Like any computer, they can occasionally get confused, for example after a power spike, a brief outage or a communication hiccup between the units. Cutting the power completely lets the boards shut down and start again from scratch.
A reset can clear a stuck state, re establish communication and remove a temporary fault from the display. In many homes, that is all that is needed after a storm. What it cannot do is repair a damaged part, refill lost refrigerant or unblock a drain. If the same problem returns after a reset, something physical needs attention.
Method one, the full power reset
This is the most effective reset for most situations, and it only takes a few minutes.
- Switch the system off with the remote or wall controller.
- Go to your switchboard and find the breaker for the air conditioner. It may be labelled air conditioner, AC or heat pump.
- Switch that breaker off.
- If there is an isolator switch beside the outdoor unit, you can switch it off as well.
- Wait at least five minutes. This allows stored charge in the boards to drain so they restart properly.
- Switch the isolator back on, then the breaker.
- Wait a minute or two for the boards to start up.
- Switch the system on with the remote and select your mode and temperature.
Give the system ten minutes or so to settle before judging whether the reset worked. The outdoor unit may wait a few minutes before starting the compressor, which is normal after a restart.
A reset only involves switches. Never open the switchboard cover, the isolator box or either unit. If a breaker will not stay on, leave it off and call a licensed professional.
Method two, resetting the remote
Sometimes the problem lies with the remote rather than the unit. Odd settings, a frozen display or buttons that do nothing can often be fixed by resetting the remote.
- Remove the batteries from the remote.
- Wait a minute or so.
- Fit fresh batteries of the correct type, checking the direction.
- If your remote has a small reset button, often recessed, press it gently with the tip of a pen.
- Set the clock if the remote asks for it.
- Point the remote at the indoor unit and send a command, listening for the beep.
Resetting the remote clears its own settings, so you may need to set the clock, timers and preferences again. Our guide on a Mitsubishi Electric remote not working has more remote tips.
Method three, wired controllers
If your system uses a wall controller, a full power reset at the breaker usually restarts the controller too, because it takes power from the indoor unit. After the restart, check the controller time, schedules and settings. Some controllers keep their settings through a power cut, while others need them entered again. It is worth photographing your controller settings once, so you can restore them quickly after any outage.
Using the emergency or manual button
Many Mitsubishi Electric wall units have a small manual or emergency operation button on the indoor unit, often hidden behind the front panel. It lets you run the system without the remote, usually in a default mode. It is handy if the remote is lost or broken, and it can help you work out whether the remote or the unit is at fault. If the unit starts with the button but not with the remote, the remote is the likely problem. Check the manual for your model to find the button and learn what it does.
When to reset
A reset makes sense in these common situations around the home.
- After a storm, blackout or flickering power.
- An unresponsive system with the breaker still on.
- One off codes after unusual conditions.
- Systems that seem stuck in a strange mode.
- Units that ignore commands after a remote battery change.
Why waiting five minutes matters
It is tempting to flick the breaker off and straight back on. However, the boards contain capacitors that hold charge for a while after the power goes off. If you restore power too quickly, the processor may not fully shut down, and the glitch may survive the reset. Waiting several minutes lets everything drain and start fresh. On larger outdoor units, a slightly longer wait does no harm.
Resetting after a storm
Storms are the most common reason for a reset. A surge or blackout can leave the indoor and outdoor boards out of step, show a communication code or make the system ignore the remote. Before resetting, check that the storm has passed and the power supply is stable. Then do the full power reset described above. If the system returns to normal, no further action is usually needed. If problems continue, a board may have been damaged and needs testing.
Resetting after a long break
At the start of summer or winter, many systems switch on for the first time in months. If the system behaves oddly on that first run, a full power reset is a reasonable first step. Before that, though, wash the filters and clear the outdoor unit, because dust and debris build up over a quiet season.
When the remote and unit disagree
Sometimes the remote shows one setting while the unit does another, perhaps after someone used the manual button or the app. Resetting the remote and sending a fresh command usually brings them back into line. If you use an app as well, check the app shows the same settings. Our guide to Mitsubishi Electric Wi Fi and app setup explains app control.
When a reset will not help
Resetting repeatedly is not a fix, however tempting it may be on a hot afternoon. Stop and book a technician if any of these apply.
- The same code returns soon after each reset.
- The breaker trips again when the system starts.
- You smell burning or see scorch marks.
- Water is leaking from the indoor unit.
- Ice forms on the coil or pipes.
- The outdoor unit makes grinding or banging noises.
In these cases, repeated resets can make things worse, especially for compressor and electrical faults. Our repair page explains what happens during a repair visit.
Is resetting bad for the system?
An occasional reset does no harm. The system is designed to cope with power cuts, and a controlled restart is gentler than a sudden blackout. However, repeatedly cutting power while the compressor is struggling to start, or while an electrical fault is present, can add stress to parts that are already weak. In short, one reset to clear a glitch is fine, while a routine of daily resets is a sign that something needs fixing.
Apartments and shared switchboards
In some apartments, the breaker for your air conditioner sits in a shared meter room rather than inside your home. If you cannot find it, building management or strata can help. The outdoor unit may also be on a rooftop or in a plant area that needs access. In that case, the remote reset and the manual button on the indoor unit may be the only steps you can take yourself until access is arranged.
Reading the code before you reset
If a lamp is blinking or the controller shows a code, note it down before resetting. Once you cut the power, the display may clear and you could lose that information. Our guide on how to check Mitsubishi Electric error codes explains how to read it. The code tells the technician where to start if the problem returns.
Resetting a multi head system
On a system with several indoor units sharing one outdoor unit, the outdoor unit and all indoor units often share a power supply through the outdoor unit. A breaker reset therefore restarts everything at once. After the restart, switch each indoor unit back on and check that they are all in compatible modes, because mixed heating and cooling requests can stop some rooms working.
Resetting the filter reminder
Some models remind you to clean the filters after a set amount of running time. This is not a fault, and a power reset will not necessarily clear it. Clean the filters, then follow the manual to reset the reminder, which often involves pressing a specific button on the remote or unit. Our guide to cleaning Mitsubishi Electric filters explains filter care.
After the reset, what to check
- The mode is correct for the season.
- The set temperature asks for cooling or heating.
- Timers and schedules are set as you want them.
- The indoor and outdoor units both start.
- No code or blinking lamp returns.
If all of these look right, the reset has done its job and no further action is needed.
Resetting ducted systems
Ducted systems usually have a wall controller and an indoor fan coil in the roof or under the floor. A full power reset at the breaker restarts the fan coil, the outdoor unit and the controller together. After the restart, check zone settings as well as mode and temperature, because some controllers return zones to a default state. If the controller stays blank after a reset, the fan coil may not be getting power, and a technician should check it. Our ducted page explains ducted systems in more detail.
A reset checklist to keep near the switchboard
Writing a short checklist and keeping it near the switchboard saves time when something goes wrong.
- Which breaker controls the air conditioner.
- Where the outdoor isolator is.
- How long to wait before restoring power.
- Where the manual button sits on the indoor unit.
- Who to call if the reset does not help.
Labelling the breaker clearly is especially useful in homes with several air conditioners or a crowded switchboard.
Keeping resets to a minimum
Most systems should rarely need a reset. If you find yourself resetting often, there is likely an underlying cause, such as power quality issues, loose connections or a component starting to fail. A service can catch these early. Our service page explains what a service covers.
What to tell us if the reset fails
- What happened before you reset, and any code you saw.
- Whether the system started after the reset.
- Whether the problem returned, and how quickly.
- Any storms, outages or recent work on the system.
- The model numbers of the indoor and outdoor units.
Final thoughts on how to reset Mitsubishi Electric air conditioner units
Learning how to reset Mitsubishi Electric air conditioner units safely gives you a quick way to clear glitches after storms and outages. Use a full power reset at the breaker, reset the remote if it misbehaves and always note any code first. A reset that works once is fine. A reset you need again and again is a warning sign.
If the problem keeps coming back, book a Mitsubishi Electric technician to find the cause.
Frequently asked questions
How do I reset my Mitsubishi Electric air conditioner?
Switch the system off, turn off its breaker for at least five minutes, then turn the breaker back on and restart the system.
How long should I leave the power off?
At least five minutes, so stored charge drains and the boards restart cleanly.
How do I reset the remote?
Remove the batteries, wait, fit fresh ones and press the small reset button if your remote has one.
Will a reset clear an error code?
It may clear a temporary fault, but if the code returns, the system has a real problem that needs a technician.
Is there a button on the unit itself?
Many wall units have a manual or emergency button, often behind the front panel. Check your manual.
When should I not reset?
Do not keep resetting if the breaker trips, you smell burning, water leaks or the same code returns.